| Quantity: | |
|---|---|
0558001625 0558003914 0558006014 0558006141
PT36
1. Remove shield retainer.
If the shield retainer is difficult to remove, try to screw the nozzle retainer tighter to relieve pressure on
2. Inspect mating metal surface of shield and retainer for nicks or dirt that might prevent these two parts from
forming a metal to metal seal. Look for pitting or signs of arcing inside the shield. Look for melting of the
shield tip. Replace if damaged.
3. Inspect diffuser for debris and clean as necessary. Wear on the top notches does occur, effecting gas volume.
Replace this part every other shield replacement. Heat from cutting many small parts in a concentrated area
or when cutting material greater than 0.75" (19.1mm) may require more frequent replacement
4. Unscrew nozzle retainer and pull nozzle straight out of torch body. Inspect insulator portion of the nozzle
retainer for cracks or chipping. Replace if damaged.
Inspect nozzle for:
• melting or excessive current transfer
• gouges from internal arcing
• nicks or deep scratches on the O-ring seating surfaces
• O-ring cuts, nicks, or wear
• Remove hafnium particles (from the electrode) with steel wool
Replace if any damage is found.
Discoloration of internal surfaces and small black starting marks are normal and do not effect cutting peformance.
If the holder was tightened sufficiently, the electrode may unscrew without being attached to the electrode
holder. When installing the electrode, use only sufficient force to adequately secure the electrode.
5. Remove electrode using electrode removal tool.
6. Disassemble electrode from electrode holder. Insert flats on the holder into a 5/16" wrench. Using the elec-
trode tool, rotate electrode counter-clockwise to remove. Replace electrode if center insert is pitted more
than 0.09" (3/32").
7. Remove electrode holder from torch body. Hex on the end of the electrode holder removal tool will engage
in a hex in the holder.
The electrode holder is manufactured in two pieces. Do not disassemble. If the holder is damaged, re-place the electrode holder assembly.
8. Disassemble electrode holder and gas baffle. Carefully remove O-ring from electrode holder and slide baffle from holder. Inspect nozzle seating surface (front edge) for chips. Look for cracks or plugged holes. Do not attempt to clear holes. Replace baffle if damaged.
Check all O-rings for nicks or other damage that might prevent O-ring from forming a gas/water tight seal.
0558003914-C PT-36 电极 Electrode
0558003914-F PT-36 电极 Electrode
0558005459ATTC PT-36 电极 Electrode
0558003928ATTC PT-36 电极 Electrode
0558012000ATTC PT-36 电极 Electrode
0558006010ATTC PT-36 喷嘴 Nozzle
0558006014ATTC PT-36 喷嘴 Nozzle
0558006018ATTC PT-36 喷嘴 Nozzle
0558006020ATTC PT-36 喷嘴 Nozzle
0558006023ATTC PT-36 喷嘴 Nozzle
0558006025ATTC PT-36 喷嘴 Nozzle
0558006030ATTC PT-36 喷嘴 Nozzle
0558006036ATTC PT-36 喷嘴 Nozzle
0558006041ATTC PT-36 喷嘴 Nozzle
0558011619ATTC PT-36 喷嘴 Nozzle
Plasma Cutting Consumables Electrode 0558003914 Nozzle 0558006014 Shield For Plasma Torch PT36
1. Remove shield retainer.
If the shield retainer is difficult to remove, try to screw the nozzle retainer tighter to relieve pressure on
2. Inspect mating metal surface of shield and retainer for nicks or dirt that might prevent these two parts from
forming a metal to metal seal. Look for pitting or signs of arcing inside the shield. Look for melting of the
shield tip. Replace if damaged.
3. Inspect diffuser for debris and clean as necessary. Wear on the top notches does occur, effecting gas volume.
Replace this part every other shield replacement. Heat from cutting many small parts in a concentrated area
or when cutting material greater than 0.75" (19.1mm) may require more frequent replacement
4. Unscrew nozzle retainer and pull nozzle straight out of torch body. Inspect insulator portion of the nozzle
retainer for cracks or chipping. Replace if damaged.
Inspect nozzle for:
• melting or excessive current transfer
• gouges from internal arcing
• nicks or deep scratches on the O-ring seating surfaces
• O-ring cuts, nicks, or wear
• Remove hafnium particles (from the electrode) with steel wool
Replace if any damage is found.
Discoloration of internal surfaces and small black starting marks are normal and do not effect cutting peformance.
If the holder was tightened sufficiently, the electrode may unscrew without being attached to the electrode
holder. When installing the electrode, use only sufficient force to adequately secure the electrode.
5. Remove electrode using electrode removal tool.
6. Disassemble electrode from electrode holder. Insert flats on the holder into a 5/16" wrench. Using the elec-
trode tool, rotate electrode counter-clockwise to remove. Replace electrode if center insert is pitted more
than 0.09" (3/32").
7. Remove electrode holder from torch body. Hex on the end of the electrode holder removal tool will engage
in a hex in the holder.
The electrode holder is manufactured in two pieces. Do not disassemble. If the holder is damaged, re-place the electrode holder assembly.
8. Disassemble electrode holder and gas baffle. Carefully remove O-ring from electrode holder and slide baffle from holder. Inspect nozzle seating surface (front edge) for chips. Look for cracks or plugged holes. Do not attempt to clear holes. Replace baffle if damaged.
Check all O-rings for nicks or other damage that might prevent O-ring from forming a gas/water tight seal.
0558003914-C PT-36 电极 Electrode
0558003914-F PT-36 电极 Electrode
0558005459ATTC PT-36 电极 Electrode
0558003928ATTC PT-36 电极 Electrode
0558012000ATTC PT-36 电极 Electrode
0558006010ATTC PT-36 喷嘴 Nozzle
0558006014ATTC PT-36 喷嘴 Nozzle
0558006018ATTC PT-36 喷嘴 Nozzle
0558006020ATTC PT-36 喷嘴 Nozzle
0558006023ATTC PT-36 喷嘴 Nozzle
0558006025ATTC PT-36 喷嘴 Nozzle
0558006030ATTC PT-36 喷嘴 Nozzle
0558006036ATTC PT-36 喷嘴 Nozzle
0558006041ATTC PT-36 喷嘴 Nozzle
0558011619ATTC PT-36 喷嘴 Nozzle
Plasma Cutting Consumables Electrode 0558003914 Nozzle 0558006014 Shield For Plasma Torch PT36