| Quantity: | |
|---|---|
120837 020607 020424 020608 220021
Hypertherm
The MAX200 system is designed to require very little regular maintenance under normal use. The following torch, torch leads, torch coolant and power supply routine maintenance checks are suggested to keep your system in top running condition:
Torch and Torch Leads
Always inspect the torch consumable parts and torch main body prior to cutting. Worn or damaged parts can cause gas and water leaks which can affect the cut quality. Check for pitting and burn marks on the consumable parts and replace, if necessary. See Changing Consumable Parts in Section 4 of the MAX200 Instruction Manual (#800870 – Hand Torch, or #800980 – Machine Torch).
The torch leads should be checked occasionally for cracking and damage.
Torch Coolant
A standard mixture of propylene glycol (30%), deionized water (69.9%) and benzotriazole (0.1 %) is recomended. Refer to Appendix B for Torch Coolant Requirements and the Material Safety Data Sheets on propylene glycol and benzotriazolefor data on safety, handling, and storage.
Power Supply
Inspect the power supply on a routine basis.
• Check the exterior for any damage. If there is damage, ensure it does not affect safe operation of the power supply.
• Remove covers and inspect the interior. Check wiring harnesses and connections for wear and damage. Check for loose connections and look for areas of discoloration due to overheating.
• At the rear of the power supply, inspect the particle filter element of the water/coolant subassembly. In the event that the filter becomes excessively dirty, torch coolant flow can slow down causing the flow switch to open (turn off) and make the coolant flow interlock status LED illuminate. The filter turns to a browish color when dirty. Replace the filter element (027005) when it starts to change color.
• Every 2 weeks, inspect the air filter in the front panel of the power supply by removing the access cover and lifting the filter out. Replace filter (027441) when dirty.
• Every 6 months, flush the power supply of its torch coolant and replace with new coolant (028872).
Tube 020963
Electrode 120547
Electrode 220021
Swirl Ring 020617
Swirl Ring 020604
Swirl Ring 020607
Nozzle 020616
Nozzle 020605
Nozzle 020689
Nozzle 020611
Nozzle 020608
Retaining Cap 120837
Retaining Cap 020423
Shield 020448
Shield 020424
Shield 020688
Plasma Electrode 220021 Nozzle 020608 Shield 020424 Swirl Ring 020607 For MAX200 Torch
The MAX200 system is designed to require very little regular maintenance under normal use. The following torch, torch leads, torch coolant and power supply routine maintenance checks are suggested to keep your system in top running condition:
Torch and Torch Leads
Always inspect the torch consumable parts and torch main body prior to cutting. Worn or damaged parts can cause gas and water leaks which can affect the cut quality. Check for pitting and burn marks on the consumable parts and replace, if necessary. See Changing Consumable Parts in Section 4 of the MAX200 Instruction Manual (#800870 – Hand Torch, or #800980 – Machine Torch).
The torch leads should be checked occasionally for cracking and damage.
Torch Coolant
A standard mixture of propylene glycol (30%), deionized water (69.9%) and benzotriazole (0.1 %) is recomended. Refer to Appendix B for Torch Coolant Requirements and the Material Safety Data Sheets on propylene glycol and benzotriazolefor data on safety, handling, and storage.
Power Supply
Inspect the power supply on a routine basis.
• Check the exterior for any damage. If there is damage, ensure it does not affect safe operation of the power supply.
• Remove covers and inspect the interior. Check wiring harnesses and connections for wear and damage. Check for loose connections and look for areas of discoloration due to overheating.
• At the rear of the power supply, inspect the particle filter element of the water/coolant subassembly. In the event that the filter becomes excessively dirty, torch coolant flow can slow down causing the flow switch to open (turn off) and make the coolant flow interlock status LED illuminate. The filter turns to a browish color when dirty. Replace the filter element (027005) when it starts to change color.
• Every 2 weeks, inspect the air filter in the front panel of the power supply by removing the access cover and lifting the filter out. Replace filter (027441) when dirty.
• Every 6 months, flush the power supply of its torch coolant and replace with new coolant (028872).
Tube 020963
Electrode 120547
Electrode 220021
Swirl Ring 020617
Swirl Ring 020604
Swirl Ring 020607
Nozzle 020616
Nozzle 020605
Nozzle 020689
Nozzle 020611
Nozzle 020608
Retaining Cap 120837
Retaining Cap 020423
Shield 020448
Shield 020424
Shield 020688
Plasma Electrode 220021 Nozzle 020608 Shield 020424 Swirl Ring 020607 For MAX200 Torch