| Quantity: | |
|---|---|
420240 420249 420258 420243 420252 420261 420246 420255
Hypertherm
Bend radius requirements for hoses, cables, and leads
The following hoses, cables, and leads cannot bend beyond a minimum bend radius of 15.25 cm (6 inches): n
Pilot arc lead n
Coolant hose set n
Power cable n
CAN cable n
3-gas hose bundle for the Core gas connect console n
5-gas hose bundle for the VWI or OptiMix gas connect console n
Gas supply hoses
Distance requirements between high-frequency leads and control cables
Interference and electrical noise can occur if high-frequency leads (such as the pilot arc and negative leads) are too close to control cables (such as the 120 VAC power, CAN, and EtherCAT® cables).
If possible, use a separate track to isolate each lead and cable.
If separate tracks are not possible, Hypertherm recommends a minimum separation distance 150 mm (6 inches) between the high-frequency leads and control cables. Separate the pilot arc lead, negative lead, or any power cables that have a voltage higher than 120 VAC from the following: n
CAN cable n
Power cable (120 VAC) n
CNC lead (EtherCAT, serial RS-422, or discrete lead)
Distance requirements for ventilation and access n
Ventilation q
Do not block the ventilation louvers on the corners or bottom panels of the front and back of the plasma power supply. A separation distance of least 1 m (3.3 feet) is required for ventilation. q
Do not block the ventilation louvers on the gas connect console. A separation distance of least 1.27 cm (0.50 inch) is required for ventilation. q
Do not block the ventilation louvers on the torch connect console. You must use the mounting brackets to allow space between the console and mounting surface. n
Service and maintenance access – Hypertherm recommends a minimum distance of 1 meter (3.3 feet) between the plasma power supply and other system components, or between the plasma power supply and an obstacle.
Shield 420491
Shield 420228
Shield 420237
Shield 420246
Shield 420255
Shield 420513
Shield 420327
XPR300 Plasma Accessories Electrode Nozzle Shield 420240 420249 420258 420243 420252 420261 Shield 420246 420255
Bend radius requirements for hoses, cables, and leads
The following hoses, cables, and leads cannot bend beyond a minimum bend radius of 15.25 cm (6 inches): n
Pilot arc lead n
Coolant hose set n
Power cable n
CAN cable n
3-gas hose bundle for the Core gas connect console n
5-gas hose bundle for the VWI or OptiMix gas connect console n
Gas supply hoses
Distance requirements between high-frequency leads and control cables
Interference and electrical noise can occur if high-frequency leads (such as the pilot arc and negative leads) are too close to control cables (such as the 120 VAC power, CAN, and EtherCAT® cables).
If possible, use a separate track to isolate each lead and cable.
If separate tracks are not possible, Hypertherm recommends a minimum separation distance 150 mm (6 inches) between the high-frequency leads and control cables. Separate the pilot arc lead, negative lead, or any power cables that have a voltage higher than 120 VAC from the following: n
CAN cable n
Power cable (120 VAC) n
CNC lead (EtherCAT, serial RS-422, or discrete lead)
Distance requirements for ventilation and access n
Ventilation q
Do not block the ventilation louvers on the corners or bottom panels of the front and back of the plasma power supply. A separation distance of least 1 m (3.3 feet) is required for ventilation. q
Do not block the ventilation louvers on the gas connect console. A separation distance of least 1.27 cm (0.50 inch) is required for ventilation. q
Do not block the ventilation louvers on the torch connect console. You must use the mounting brackets to allow space between the console and mounting surface. n
Service and maintenance access – Hypertherm recommends a minimum distance of 1 meter (3.3 feet) between the plasma power supply and other system components, or between the plasma power supply and an obstacle.
Shield 420491
Shield 420228
Shield 420237
Shield 420246
Shield 420255
Shield 420513
Shield 420327
XPR300 Plasma Accessories Electrode Nozzle Shield 420240 420249 420258 420243 420252 420261 Shield 420246 420255